→ Knocking down bit https://bitsbits.com/product/bitsbits-sf525-surfacing-router-bit/
→ Fuji HVLP sprayer https://amzn.to/3MLH9Wy
→ Milk Paint https://amzn.to/3TiT00H
I latterly finished an identical farm desk base and an out of doors kitchen sink island. I timed the construct of those so I may spray them concurrently. For the colour, we selected Tuscan Purple Milk Paint by means of Basic Finishes. The can supplies numerous information on how it may be implemented, together with directions for spraying, which is the course I’m taking. With a 1.8mm tip put in I will load the sprayer and get to paintings.
Right here’s a tip for pouring from a can. Use a large strip of tape to act as a spout. Lower a V notch the place you wish to have to pour, and use an axe, knife, or screwdriver to poke a hollow within the rim of the can. Now, whilst you pour, the tape will act as a spout and drain the vast majority of the surplus again into the can. The outlet within the rim will permit it to drain again into the can if you wish to have to position the lid again on loosely.
The strainers I’m the use of make the pouring procedure somewhat lengthy. On this case, it’s OK as a result of I’m buying and selling my CNC hard work for some shifting hard work to lend a hand get those initiatives sprayed.
Whilst the milk paint drips into the cup, I began a few of my CNC paintings. Zach and Jason are from Again 40 Customs in Tupelo, Mississippi they usually make numerous epoxy river tables. Those walnut slabs can be for tables however ahead of the tables can also be poured they prefer to rather flatten the slabs so they’re going to leisure flat at the backside of the paperwork.
After one slab, we’re again outdoor to get started spraying. First, the desk base. I discovered temporarily how smartly the protection is with this milk paint. I’m spraying outdoor with a slight breeze on a unprecedented low-humidity day, so the paint is drying speedy. I may most likely have got away with spraying the second one coat straight away after the primary, however as a result of there’s different paintings to be done, I switched again to the store to stay shifting.
Every other slab with the similar function. Flatten with out disposing of numerous subject material. The SF525 bit I’m the use of is flying in the course of the subject material, so thru the remainder of the cuts, I regularly greater the aggressiveness.
Again outdoor for a 2d coat of Tuscan Purple, additionally ensuring to seal the ground of the legs. I’ll have leg levelers put in so they’re going to by no means be sitting in water, however I would like to seal them just right anyway.
Slab #3 will get flattened, and by means of now, I had a beautiful just right concept of what number of passes and what sort of subject material to take away. This was once essentially the most competitive minimize at .200” DOC, 1.5” stepover, and 500 IPM. At this level, I’m maxing out the gadget’s commute and will simplest building up the intensity according to move. Every other factor I realized is how a lot more difficult epoxy is on surfacing bits. It cuts the epoxy simply effective, however it cuts thru this walnut like a scorching knife thru butter. It’s an outstanding bit.
In addition they introduced 3 smaller slabs to be used as floating cabinets, which have been sufficiently small to use at the jointer. This can be a Hammer A3-41 jointer planer combo gadget with a 16” lengthy cutter head. Hardly ever does a task arise desiring the overall width, but if it does, it’s extremely gratifying. Knocking down with the jointer will at all times be sooner than with the CNC. The CNC has a miles larger capability.
After the primary couple of forums, somewhat additional push was once certainly preferred. After all, the guards have been got rid of for photographic readability, and also you will have to by no means take the guards off your gadget simply since you noticed some dufus like me do it in a video.
Toybox fronts have been up subsequent. Those are paint-grade initiatives with a personalised entrance. The primary mentioned Hood, the second one mentioned Toy Field, and we waited at the 3rd for spelling affirmation.
Now the time I used to be looking ahead to. Gazing folks transfer the heavy stuff I made. That’s one of the simplest ways to transfer stuff; Watch folks do it.
4 chunks of firewood have been used to stay it off the grass. And we rolled it the wrong way up for spraying. That means, identical to the desk base, I may spray the ground to get higher coverage from flooring moisture. After all, the leveling ft will keep in touch with the cement ground, no longer the true picket.
A snappy notice about my canines. They pop into the body right here and there however know that my spouse was once outdoor, maintaining them again whilst I used to be spraying.
Extra trade as same old. One base coat for the preliminary protection and a 2d coat to make sure that general protection. General, I’m more than happy with how smartly this product covers. That is my first enjoy with Basic Finishes Milk Paint, so I’m curious how smartly it holds up longer term. I learn that it does slightly smartly outdoor, so I’m taking a look ahead to minimum, if any, repairs over the following couple of years.
