Tag Archives: wood project
Insulated and Heated Cat or Dog House
Associate hyperlinks to pieces used:
→ Thermostat https://amzn.to/3CbHZYm
→ Heating component https://amzn.to/3vqITN6
→ lamp base https://amzn.to/3G2wcwH
→ Vinyl door flap https://amzn.to/3jCuWce
It’s getting chilly, because it does each wintry weather.. My daughter has an outside cat that in most cases sleeps in our storage. We had a small material cave/mattress factor for it, and whilst that works properly for many nights, we need to supply a bit extra heat throughout the in point of fact chilly nights. A handy guide a rough symbol seek for inspiration, a snappy SketchUp interpretation, and fabrics run to begin the construct.
The principle building subject material I went with used to be Advantech OSB floor. In part as it’s just about water-proof and most commonly as it used to be the least dear 3/4” thick sheet excellent I may purchase in the neighborhood.
OK, I’m simply construction a field. Not anything fancy. A couple of desk noticed cuts later, and I’ve a stack of six rectangles. I used to be unsure at the door dimension, however I didn’t need it as huge because the vinyl door flap I bought. So I drew what seemed suitable at the entrance panel.
After which use a mixture of my anti-kickback curler guides, and the desk noticed to plunge one immediately minimize in keeping with facet of the outlet. I drew a centerline on every of the cuts to line up with the centerline of the blade, which I drew at the fence. That method, I no less than knew the blade used to be focused at the duration of the road. I didn’t fear about getting it throughout at this step.
And that’s as a result of I used a velocity sq. and a jigsaw to finish the cuts to shape a pleasing crisp inside of nook.
Identical to the outdated days, glue and brad nails to carry the whole lot in combination. Beginning with the 4 aspects and most sensible.
A well-sealed OSB construction would almost definitely be excellent sufficient and dangle the warmth properly sufficient, however we opted so as to add 3/4” Styrofoam insulation. It used to be reasonably priced and simple so as to add. A razor blade and a immediately edge are all this is had to minimize it.
The plastic lamp base I’m the use of wishes a bit little bit of the froth got rid of for twine get right of entry to. That’s simple sufficient with a hollow noticed. I adopted the opening noticed with a standard drill bit sized for the extension twine I selected to hook the whole lot up.
Then the again insulation panel is got rid of to make all of the connections at the bench. I made a channel at the back of the insulation to feed the wires from the thermostat to the lamp base. The thermostat connection is extremely easy. The black twine from the extension twine is the ability twine. It connects to the black “load” twine at the thermostat. When the temperature lowers, inflicting the thermostat circuit to near, energy exits by means of the crimson twine. I hooked up a small piece of black twine to the top of it and hooked up it to the lamp base. The white impartial twine within the extension twine will get hooked up without delay to the impartial at the lamp base. The lamp base and thermostat are each easy electronics that didn’t have a floor, so no floor used to be used.
After reinstalling the again panel, the lamp base and thermostat are every secured with a couple of screws. I used a standard mild bulb to check the setup. For somebody short of to make this know that I used a 150w ceramic heating component, and it ended up being too as regards to the highest. Only a heads as much as mount it decrease and almost definitely centralized. Some ceiling foam insulation melted because of the component being too as regards to the highest. I’ll duvet that during a follow-up video.
I sought after no less than some of the panels to be detachable, so I most effective put in the ground panel with screws. This may permit higher get right of entry to if I wish to trade the rest inside of.
For the legs, I went with some 1-5/8” sq. cedar I had already milled from earlier use. All I wanted used to be a rabbet to mount them to the field. Simple sufficient with two cuts on the desk noticed, ensuring the closing minimize had the waste left of the blade and used to be no longer trapped between the blade and the fence.
Rails don’t seem to be wanted right here, however they lend a hand save you the cat from knocking the meals bowl off. Scrap picket to the rescue once more. I had a work of poplar that used to be best possible for this. A suitable width and a knot lifeless heart within the board. One rail from every facet of the knot.
You guessed it; glue and brad nails to carry the rails on.
The door used to be too lengthy, so I trimmed it and secured it with 3 screws. Creating a trim piece to hide the highest of the vinyl door screws is one thing I thought to be however handed on because of the time constraint.
The general piece of the puzzle used to be to chop a work of scrap carpet for the ground.
And that’s it. A easy, comfy, insulated, heated house for my daughter’s cat to stick heat at night time. Now all I’ve to do is wait about 6 months for my spouse to invite, “are you ever going to color that cat space?” to which I’ll answer, “simply because a person says he’s going to do one thing doesn’t imply you need to remind him each 6 months!”
Megan’s Anarchist’s Tool Chest at Age… (it’s Complicated) – Lost Art Press
I figure out of 2 Anarchist’s Tool Chests (ATC) of 2 other ages – however for 2 several types of paintings. In 2012, I constructed the only I’ve at house in my previous second-floor house store and in Chris’s previous basement store. For a very long time, it held an almost-complete moment set of hand equipment for development furnishings. Once I left PopWood (PW) in 2017, I bought nearly all of my doubles (needed to pay the loan one way or the other!), so my chest at house is now most commonly for equipment I exploit for operating on stuff round the home. It does nonetheless have some of the similar equipment as at paintings (I want chisels and a block aircraft at each puts), and it has some stuff I by no means use however can’t (but) endure to eliminate. And there are a couple of equivalent pieces in my chest at paintings. I’m no longer extraordinarily sentimental…however I’m no longer just about as ruthless as Chris relating to divesting myself of items I don’t really want.
My chest at paintings is nearly 5 years previous; it’s the only I constructed within the first ATC elegance I taught in our store after leaving PW (I imagine in February 2018).
There are a couple of pieces that trip backward and forward now, however for probably the most phase, my furniture-making equipment are at the Lost Art Press store. Whilst there’s various room in my more recent basement store and I’ve two benches there, I’m spoiled by way of the sunshine coming within the home windows at paintings – so every time imaginable, I like to paintings the place I will higher see…and the place I will extra readily ask for a hand in lifting heavy stuff (thanks, Chris).
My stock has most commonly remained the similar for the decade, but if I started educating much more (in 2018), I started obtaining extras of stuff that scholars have a tendency to borrow (both as a result of they don’t personal that instrument or as a result of they purchased theirs the place they shouldn’t). Educating is why my equipment have blue dots on them and/or blue gaffer’s tape – for speedy identity. As Chris did along with his stock, I’ll paintings my manner down in the course of the tills, then to the racks and chest surface. However my pictured groupings aren’t as explicit – to a point, I simply squeezed in combination what have compatibility on best of my chest. And as along with his, a few of these are equipment that:
• I’ve had for years and that I’m proud of. “It’s mine, I let you know. My very own. My treasured. Sure, my treasured.” (No use to check out some other…until it’s blue or cat-shaped)
• Have been made by way of a chum/any person I like
• Got to me by way of a chum/any person I like
• I do not know why I’ve this actual instrument
I even have a couple of different equipment jumbled in with the scholar equipment, at the cabinets close to my table and at the instrument wall. (Ones that merely absorb an excessive amount of room in my chest vs. how ceaselessly I want them.)
The Best Until
My best until holds the stuff I achieve for probably the most – each in categories and in my very own paintings, in conjunction with a couple of small issues that don’t have compatibility in different places.
Block Planes & Bizarre Bollocks
The Lie-Nielsen block planes (a No. 60-1/2 and No. 102) in spite of everything have their very own cubbies as of closing week (I’ve been which means to try this for some time, after all). Within the cubby with my No. 102 is the place I now stay the instantly and Phillips hex guidelines for my Part’ary motive force (as a result of that’s the place they have compatibility properly and received’t get misplaced). Additionally within the best until are the Torx guidelines for a similar. I stay my soft-jaw pliers shut at hand as a result of I’ve a marginally of arthritis in each fingers now, so it turns out to be useful for tightening fences on more than a few equipment (and getting issues unfastened). I exploit the Lie-Nielsen brush to take away sawdust from all my equipment ahead of I wipe them with my woobie (which hangs on my bench mild) and stow them again in my chest. The (fairly gross – sorry) listening to coverage is after all essential for the usage of energy equipment, but in addition whilst six scholars are slicing dovetails (hand-tool woodworking isn’t all the time quiet). The Operating Fingers cream will get dipped into at least 4 to 5 instances each day – extra in wintry weather (oh, for a greater and lasting resolution for my dry pores and skin). And I achieve for the cat treats much more instances than that….
Dovetail Marking/Checking Gear
Sure, after all I exploit marking knives for issues instead of dovetailing – however I do minimize numerous dovetails. The only at the some distance left is my long-time favourite – a Blue Spruce spear-point knife made by way of Dave Jeske. The remainder (from left: a Veritas “Workshop Placing Knife,” A Czeck Edge Gear “Kerf Cadet II” and some other of Dave’s knives…that I purchased as it’s blue) are knives I mortgage to scholars. The Lufkin No. 137C is the small sq. I exploit to test dovetails and that I’ll let scholars use. (It’s uncommon that any however the slender blade is within the instrument, despite the fact that sometimes I’ll use the 2-1/2″ rule. The miter blades got here with it, so I’ve stored them (they don’t absorb a lot room within the field). Above the Lufkin sq. are 3 dovetail templates. At best is the Woodjoy equipment model I’ve had since about 2006, then a Woodjoy that was once given to me (I haven’t forgotten I owe the donor a Dutch Tool Chest ebook after I end it…simply in case he’s studying!) from an up to date design with an extended inventory (to suit throughout two 3/4″-thick tailboards for marking gang cuts). On the backside is the first-one-off-the-production-line Crucible Gear Dovetail Template this is in accordance with the Woodjoy model (with permission and royalties paid to the clothier). To the proper of the ones is the R. Murphy Hand Carving and Dental Knife I inherited from my grandfather; I exploit it maximum ceaselessly for aid cuts at the again of tails. At some distance correct is the small sq. I don’t mortgage to scholars for checking dovetails: a Vesper Gear Precision Dovetail Sq. (and its more than a few regulations). I misplaced a equivalent Starrett sq. in a category – I’m beautiful positive it was once inadvertently swept off a bench right into a trash can. So I purchased the Lufkin to switch that one. I will’t have enough money to switch the Vesper. The bins themselves are principally cubbies to give protection to and corral their contents – lazy cubbies, however they have compatibility they usually paintings!
Measuring Gear
I’ve had each the huge and small Starrett aggregate squares since nearly the day I determined to learn to make furnishings. I really like the 12″; I desire a new old-stock 6″ (mine slips)…however I’ve been announcing that for at least 5 years, so it’ll most certainly by no means occur. Then there’s an array of 6″ regulations – most commonly for loaning out. My favourite is the Starrett at backside left; it’s the very best for me to learn. The 4″ Starrett at backside correct was once simply too lovable to withstand all the way through a long-ago discuss with to Colonial Dwelling house. And I’ve two tape measures as a result of I all the time appear to be lacking one or the opposite. In the event that they’re each the place they needs to be, I most often achieve for the crimson one; its wider blade has higher standout.
Pencil (and so forth.) Corral
This far-right cubby could also be new, and already I like it. It’s such a lot more uncomplicated now to search out my .5mm pencils (all the ones at backside left). (In case you’ve ever taken a dovetailing elegance with me, you understand how I believe about those!) Along mentioned pencils is a paper knife given to me by way of Eric Brown (thanks, Eric!) – I stay looking for the very best woodworking use for it. I haven’t but, however within the interim, it doesn’t absorb a lot area. At best left is dental floss (used for operating glue into splits, or into miscuts whilst dovetailing to cover the error…I’d like to say it’s best wanted for college students). My most-used protection apparatus is that hair clip. I catch numerous crap for having my hair down in footage – however I promise you that if I’m the usage of any instrument or gadget that poses a threat of scalping (or worse) my hair is up. I’ve two lumber-marking pencils. I must discover a new house for the blue one (I a lot desire my “Unturned Pencil“); beneath the ones is shopmark stamp from Infinity Stamps. Beneath them is my paint can opener; I exploit numerous paint. Within the heart is a planing prevent that matches into a three/4” canine hollow. Adam Cherubini left it on a bench at Woodworking in The usa, circa 2013. I’m looking ahead to him to stroll in the course of the door so I will go back it to him. Beneath this is an M+R pencil sharpener that Chris gave me. (I do have picket pencils for which to make use of it; they’re on my table…which is the place this sharpener in point of fact will have to be.) Then there’s my Jap nail set (at simply $12, I feel everybody will have to have this at hand instrument). Along that could be a ceramic pencil with white “lead” (and a few additional “lead”), and two bits of eraser. I don’t know what that knob is going to (despite the fact that I feel it’s a Veritas knurling trend), so I’m afraid to pitch it. I additionally stay a small pocket book in that cubby, and my new cat-head tape measure. (I like it…but it surely’s no longer so nice for woodworking – but it surely’s nice for maintaining a tally of my increasing waistline.)
The Center Until
The center holds the equipment I exploit slightly ceaselessly – however no longer rather so ceaselessly as the ones within the best until…or that I don’t use ceaselessly, however simply ended up there because of their dimension and my to be had area (I’m speaking about you, steel spokeshaves).
Hitty Issues
At some distance left is a crappy hammer this is extraordinarily uncomfortable. (My excellent one is at house.) Chris purchased this atrocity for me as a result of he was once uninterested in my borrowing his Platonic Very best Hammer from his instrument chest. I nonetheless borrow it. (And I put this one within the pupil chest simply after taking this image.) The ball-peen hammer was once left at Woodworking in The usa by way of Peter Ross (he kindly instructed me to stay it). I exploit it for educating tips on how to “bishop” proud pins and tails (get the picket rainy, then flippantly hit it with the domed placing floor to unfold the fibers and fill small gaps). The plane-adjusting hammer was once made by way of Raney Nelson of Daed Toolworks; I exploit the 8-ounce Dunlap for atmosphere small nails…and as a aircraft hammer when it’s nearer than the only Raney made.
Slicing & Cleaving
At best are my two flush-cut saws. Handiest the highest one will get loaned. Its blade is replaceable (for when blood makes it rust). I’m no longer positive why my small router aircraft is within the heart until; I feel I moved it down after I were given the No. 60-1/2 block aircraft; it used to live the place that block aircraft now sits. The spokehaves get used so much in my “Dovetailed Shaker Tray” categories, and for the occasional different curve want. The PMV-11 aircraft blade in reality will get used so much; it’s the only I hand out in ATC categories to mark the skirt baselines off the chest (that sentence will make sense best to those that’ve learn the ebook or taken the category). I purchased it to position in my No. 3; one day I’ll in reality do this. I exploit the Bohle hacking knife for making pegs.
Bits And so on.
I really like this set of fractional brad-point bits, and I want to prevent loaning them as a result of apparently this set is now not to be had (I desire not to mortgage issues I will’t change). I even have a couple of different bits tucked away within the case, together with a damaged Insty-bit that I exploit as a countersink. Beneath is a brand-spanking-new field of tiny bits (thanks, Chris; sorry I stored borrowing yours). That lone countersink doesn’t have compatibility within the index field, so it simply rolls round within the until. The saddle sq. will get used for nearly each and every mission – specifically all the way through inventory prep (very best $14 I ever spent – a decade later and it’s nonetheless best $16.50). At best correct is my Starrett centerpunch, which will get used on each and every {hardware} set up (and which I feel is superb a laugh to make use of). Beneath it are two equipment I don’t use ceaselessly however I really like: a 4″ sliding bevel that was once a present from Fred West (it will get used every so often to mark 30º angles on Dutch instrument chests after I don’t have a bigger one handy) and a small sq. I purchased to compare it, each from Vesper Gear.
The Backside Until
This holds the stuff this is both too giant/cumbersome for the smaller heart or best until, and/or equipment that I don’t use a lot. And/or that I were given used to hiding a decade in the past…a dependancy that hasn’t utterly left me. (I’m overly protecting of my paintbrushes…and would dearly love to search out some new old-stock Purdys. If of a pre-2004 stash, do let me know.)
Brushes & Such
Gloves to give protection to my lily-white fingers (to assist minimize down at the splinters, plus picket sucks what little moisture there’s from my fingers). That Wooster brush is in unhealthy sufficient form now that I’ll mortgage it. The Purdy isn’t. The cardboard document is for cleansing my rasps (which might be at house – so that is useless). The cork is a sanding block. Above that’s the roll of blue gaffer’s tape for marking my equipment (it was once within the heart until; I simply moved it), crowned by way of the blue nail polish for a similar. On the best correct is a field of headless brads…since the drawer the place they cross is complete, and I introduced those in from house, the place I didn’t want them.
Hodgepodge
The pinch rods are stashed right here as a result of they’re too quick for measuring an ATC, and I don’t need scholars grabbing those by way of mistake when the glue is rainy. (I shortened those for operating on my staircase, however I didn’t in point of fact want them at house after that, so right here they sit down.) Oh glance – some other spokeshave! This picket one (which I really like) was once made by way of Kansas Town Tool Works (now into chapter 11). At the left are affordable dial calipers; I hardly care about caliper-level of perfection – however now and again, one has to. The Barr chisel will have to be in my instrument rack, however there’s no room ultimate due to a contemporary noticed acquisition (I tape a folded trade card over the innovative to give protection to it…and to give protection to my palms after I achieve within the until. The Zona noticed turns out to be useful now and again, however I will have to drill a hollow within the deal with and hold it at the instrument wall. I don’t ceaselessly achieve for it. On the backside heart is a heavy toothed blade from Ron Bontz intended for bopping into the corners of half-blind dovetails for more uncomplicated clean-out. It sounds in point of fact helpful – and shortly I’ll get round to chopping some half-blinds and in finding out! The closing instrument, some distance correct, is a pencil gauge that can be utilized on outdoor curves (e.g. the again of a stick chair seat) – some other present from Chris. In order that I hand over borrowing his.
Moulding Airplane Corral
I’ve maximum of my moulding planes at house (as a result of a faulty considered making by way of hand the entire substitute mouldings wanted for my area) so I most commonly use this space for stuff I wish to retailer upright (and that doesn’t in point of fact have compatibility in different places with out entering into the best way.)
Scrapers, Guidelines & Extra
The 2 scrapers I in reality use are a rather versatile Lie-Nielsen (for buying into corners) and the Crucible curved scraper (which, even with my achy fingers, is comfy to wield); those I don’t use are within the leather-based pockets beneath. The driving force guidelines don’t in point of fact belong in my instrument chest; I simply don’t know the place else to position them. The Bevel Monkey will get maximum used for atmosphere 30º angles, and the set of needle information get used to mend my planes after nearly each and every elegance (the entrance edges have a tendency to get dinged up and require submitting in order to not go away tracks).
Edge Gear
The Lucian Avery scorp and Lie-Nielsen instantly drawknife are for the entire chairs I may one day make.
Maximum Scholars’ Least-favorites Gear
I cope out (or be troubled out) the waste on dovetails; this may also be vexing to these new to those saws – however I in finding it saves numerous time on waste removing, specifically at the pin forums. Those are the one equipment my scholars steadily draw back at the usage of. (Whilst I covet Chris’s Blue Spruce Coping Noticed – that’s what I’d purchase if I have been ranging from scratch – those two Knew Ideas saws are previous pals. NB: The KC fretsaw is to be had with and with out “swivel blade clamps” – make sure that in the event you get one, that it’s “with.”)
Moulding & Rabbet Planes
I do retailer a couple of picket moulders within the moulding aircraft corral: two 1/8″ beading planes (from M.S. Bickford [top] and Philly Gear [middle] that get used at the higher skirts of ATCs and different issues); and one instantly rabbet aircraft from M.S. Bickford.
Chest Ground
Most commonly Planes
There’s numerous unused actual property at the surface, so I controlled to shoehorn all of it into one image. My No. 7 is at the highest (some other non-loaner) with the remainder of my bench planes at the left: a Sort 11 No. 5 that Chris had Jen Bower engrave for me (due to each!), and 3 easy planes (Nos. 4, 3 and a pair of). I just like the bronze as it’s more uncomplicated to document, and those get information on the vanguard so much (the graceful planes are remarkably vulnerable to throwing themselves atop holdfasts and different steel bits…). I exploit the No. 3 in my very own paintings. Above the graceful planes is a medium shoulder aircraft. To its correct is a chisel aircraft; I in finding this instrument helpful for becoming constructed ins, however no longer for furnishings paintings. It will have to cross house to my different chest. Beneath the chisel aircraft are two Veritas equipment: a right-handed skew rabbet aircraft (want I’d no longer bought the left-handed one, however oh smartly) and an edge-trimming aircraft. Along is my loved (or a phrase this is more potent than “loved”) blue Blue Spruce mallet. If that ever breaks I can be severely bereft. Above this is a small bottle of jojoba oil that I take at the street; it’s in my chest best so I don’t fail to remember it after I’m packing. Ultimate is certainly one of my massive router planes (the opposite is within the scholars’ chest). I do love a router aircraft!
Placing Racks
You might have spotted manner up at the highest that I’ve panel saws striking at the underside of my chest lid at house. On the LAP store, I borrow from the instrument wall after I’ve an extraordinary panel noticed want. So I don’t desire a surface until; my backsaws hold in the back of my chisels and different pointy equipment.
Dovetail Saws
I swear those spawn in my chest. The 2 walnut-handled ones are from Unhealthy Awl, and feature additional small handles; as a result of I exploit my DT saws so much, I desire they really feel relaxed…which is how I stopped bringing house from Ed’s Tool Retailer the Nineteenth-century Woodrough & McParlin at the left. The wee deal with is an ideal have compatibility; I assume it belonged to an excessively younger apprentice? Of the Unhealthy Awl saws, I desire my previous one, at best; it’s like an previous pair of slippers – tremendous comfy if no longer as beautiful because it as soon as was once. I want to spend extra time with the brand new one, and put on away a few of its set (I’ve been the usage of the previous one for see you later that it would double as a flush-cut noticed I feel!). On the backside is a Lie-Nielsen progressive-pitch noticed this is now not made, and that I don’t ceaselessly lend – however I hardly use it. I assume that makes me a collector. Oh pricey.
Different Backsaws
The “American Child” tenon noticed at best is a hybrid submitting with a deal with intended for youngsters. It suits me smartly. The Lie-Nielsen crosscut carcase noticed is superb – and since I don’t use it day by day, I don’t thoughts that the deal with is somewhat massive for me. On the backside is some other collectible, a crosscut carcase noticed by way of Wenzloff & Sons.
Screwdrivers
I’ve an almost-full set of Grace USA instantly screwdrivers, a Lie-Nielsen motive force “rescued” from a Chris culling (I’ll hold directly to it till the following time I clear my chest), a Phillips motive force (’purpose now and again I want one, despite the fact that I nearly all the time use slot screws) and my Part’ary motive force with a locking magnetic collar (its guidelines are in my best until).
Marking Gear
You’ll’t beat the Tite-Mark chopping gauges…and I want other people would hand over copying those. Kevin Drake merits the entire $$ for those (you’ll get them by means of Lie-Nielsen or Gear for Operating Picket). Then there’s my massive circle of relatives of dividers: 3 Starretts and two Crucibles (those all get loaned out for laying out dovetails). And oh glance…some other loaner Czeck Edge marking knife (the rubber band is so it doesn’t fall in the course of the 1/2″ hollow within the instrument rack). After all there’s my latest favourite pointy instrument: a Mathias Fenner birdcage axe (this 12 months’s beautiful and far preferred Christmas present from Chris).
Chisels
I exploit 3 of those six Lie-Nielsen bevel-edge chisels steadily (1″, for firstclass noticed cuts on 3/4″ and seven/8″ tailboard half-pins, and the three/8″ and 1/4″ for slicing dovetail waste ultimate after coping). I exploit the others after I’ve loaned out those I in point of fact like to make use of. The Blue Spruce fishtail chisel is for cleansing out corners in half-blind dovetail pin forums – I don’t want it ceaselessly, but if I do, I’m awfully happy to have it.
As Chris discussed in his ATC stock closing week, we get numerous emails about this chest and the ebook Chris revealed in 2011. I’ve a unusual courting with the ebook (about which I’ve written ahead of – sorry to copy myself). As he wrote, it’s the ebook that allowed him to hand over as editor of Widespread Woodworking Mag. If he’d no longer left, I’d by no means have grow to be editor and content material director for the logo…which was once professionally rewarding however no longer the best for my psychological well being. I’m however altogether grateful to have held had that place for 5 years. I’m much more grateful that now I once more paintings with Chris each day within the store. Each instrument chest that I construct or assist others construct strikes a chord in my memory anew of the way fortunate I’ve been.
– Fitz